Oil Injection Delete - 1979 Enticer 250

Just want to remove the oil injection. All lines are dried out and have crumbled into the belly of the sled. I'm replacing all gas lines. I'd rather use premix versus replacing all the oil lines and the oil tank.
So can I just leave the oil pump in place as it came stock? The screws are badly rusted and difficult / impossible to get to.
I know how wonderful the carb swap-out is that everyone does on these 250's; however I don't have money to spend on a carb unless this original one proves to be toast. Before the mice moved into the machine 3 years ago, this 250 was always the most dependable sled (in our family) for over 30 years.
Thanks for any help,
-Matt

Oil Injection Delete - 1979 Enticer 250

Oil Injection Delete - 1979 Enticer 250

Just want to remove the oil injection. All lines are dried out and have crumbled into the belly of the sled. I'm replacing all gas lines. I'd rather use premix versus replacing all the oil lines and the oil tank.
So can I just leave the oil pump in place as it came stock? The screws are badly rusted and difficult / impossible to get to.
I know how wonderful the carb swap-out is that everyone does on these 250's; however I don't have money to spend on a carb unless this original one proves to be toast. Before the mice moved into the machine 3 years ago, this 250 was always the most dependable sled (in our family) for over 30 years.
Thanks for any help,
-Matt

Oil Injection Delete - 1979 Enticer 250

Keinin carb troubleshooting

I have a 1981 Yamaha enticer e250 with a Keinin carb that hasn't run for years & years. The carb was removed & took it to a local snowmobile shop and they put in a new gaskets & diaphrams. I installed it & mixed gas with oil 50:1. Thought it would be better to foul a plug than run dry till bled air from oil system. I primed it with squirt bottle & fires up. I bypassed the shut off valve on side of oil tank
to be sure it wasn't that. Did pull carb apart and looks like everything is ok, but did clean and jets or holes to be sure. Since I didn't remove it originally looked like fuel line goes into silver colored nipple on side(top) and lower brass colored(bottom) nipple was vacuum line to block. needle valve was sticky but I cleaned seat & wiped needle dry. It will not run on it's own. Doesn't seem to be pulling any fuel into carb. Can't see any fuel in clear tube running up side of carb. I would greatly appreciate any feed back as I am trying to get this thing running for the kids on christmas.

Keinin carb troubleshooting

Clutch Pullers

Is there any brand of clutch puller I should avoid.
No idea who actually made Arctic Cat pullers.
A lot of them say "same as" OEM puller.

I made a puller bolt on my lathe out of what I believed
to be an old tie rod end, and thought it was pretty hard.
I tried using it on the clutch, and the long .410 inch
stem started to buckle and never popped the clutch.
I had the same problem on a Ski Doo years ago, and
that was a store bought one. Don't want to make
the same mistake again.

Is this brand okay, or do you have known better ones?
It's for the 2002 600 ZL ESR.
https://www.ebay.com/itm/EPI-Premium...Eiy3:rk:1:pf:0

Thanks!

Clutch Pullers

Sled Boggs out when I gas it

My 2003 ski doo Mach z 800 triple Idols real low just got it out of the shop had the carbs cleaned and three coil packs replaced new spark plugs new gas and I have to feather the gas for it to move and ride but If I floor it from idol it bogs down
PLEASE HELP

Sled Boggs out when I gas it

700 srx dead cylinder

Need help, PTO cylinder will not run, was running great, just all of sudden cylinder went dead, There is good compression 125 on all 3 cylinders, runs good on the right 2 cylinders, pro cylinder has good spark, good compression, I put fuel in the plug hole still will not fire, sprayed fuel in carb still will not fire, I put propane to crank seal to check for leak, did not idle up, I pulled head piston looks good from the top, Reeds look good. I am stuck what to look at next. All indicators point to bad crank seal, but it should idle up if I spray it with carb cleaner or propane , anyone got any ideas ????

700 srx dead cylinder

It's beginning to look like Christmas!

Was out in the Tucker today doing a bit of grooming. Snow at lower elevations is a bit sketchy, but at higher elevations, it's looking pretty good! The Tucker is new to our club to augment or Pisten Bully with a trail system that is too remote and narrow for the bigger PB to navigate. LET IT SNOW!!


Attachment 62366

Attachment 62368

Attachment 62370

Attached Thumbnails

     

It's beginning to look like Christmas!